Xen FAQ Booting: Difference between revisions
From Xen
Jump to navigationJump to search
OliverChick (talk | contribs) (→I get an error from Xen... (console output starting "(XEN)"): Removed - Xen 2.0 is no longer relevant) |
Rcpavlicek (talk | contribs) No edit summary |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
== I have problems getting Xen or dom0 kernel to boot, how can I set up a serial console to log and troubleshoot the boot process? == |
|||
<!-- MoinMoin name: XenFaq --> |
|||
See the [[XenSerialConsole]] wiki page. |
|||
<!-- Comment: Added link to XenFAQ2 --> |
|||
<!-- WikiMedia name: XenFaq --> |
|||
<!-- Page revision: 00000096 --> |
|||
<!-- Original date: Wed Sep 14 11:36:18 2011 (1316000178000000) --> |
|||
== I am booting my new EFI-based system. I se "Loading ramdisk..." and then it stops == |
|||
<!-- #pragma section-numbers on --> |
|||
Go into your BIOS and enable Legacy Booting (non-EFI). If it still doesn't work, upgrade the BIOS to its latest version. |
|||
<!-- ! TOC here --> |
|||
<!-- Leave this at the end --> |
|||
= Booting Xen = |
|||
== |
== Where do I find more Booting FAQs? == |
||
See [[Xen_Common_Problems#Booting]] |
|||
In Xen 2.x, you can add the <code><nowiki>physdev_dom0_hide</nowiki></code> parameter (see [[Xen Hypervisor Boot Options]] for more parameters) to hide one or more pci devices to Dom0, so you can affect them to domU. |
|||
Pci slots MUST be formatted like this: |
|||
* '''(nn:nn.n)''' |
|||
so |
|||
* <code><nowiki>(03:06.1)</nowiki></code> is correct |
|||
* <code><nowiki>(03:6.1)</nowiki></code> is NOT correct |
|||
You can get the pci bus address on a Linux system by using the lspci command (only the last bits are relevant): |
|||
<pre><nowiki> |
|||
lspci | grep Ethernet |
|||
0000:02:03.0 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet Controller (Copper) (rev 01) |
|||
0000:02:03.1 Ethernet controller: Intel Corp. 82546EB Gigabit Ethernet Controller (Copper) (rev 01) |
|||
</nowiki></pre> |
|||
Then: |
|||
* to hide the second network interface from dom0, you can then append <code><nowiki>physdev_dom0_hide=(02:03.1)</nowiki></code> to your <code><nowiki>kernel /boot/xen-2.0.gz</nowiki></code>. |
|||
* to hide multiple pci devices, simply concatenate all the pci slots address like this: <code><nowiki>physdev_dom0_hide=(02:03.0)(02:03.1)</nowiki></code> |
|||
If everything went ok, you should see the following lines after a reboot: |
|||
<pre><nowiki> |
|||
(XEN) Hiding PCI device 02:03.0 from DOM0 |
|||
(XEN) Hiding PCI device 02:03.1 from DOM0 |
|||
</nowiki></pre> |
|||
== Error about root device still mounted when it's not mounted, zombie domU that can't be killed, domU hangs under heavy I/O (e.g disk) access == |
|||
This is an unresolved problem with Xen 3.0. |
|||
You may try to [http://lists.xensource.com/archives/html/xen-users/2006-03/msg00651.html pass nousb to dom0 kernel command line], or [http://lists.xensource.com/archives/html/xen-devel/2005-07/msg00436.html pass ignorebiostables], or try to [http://lists.xensource.com/archives/html/xen-devel/2005-07/msg00468.html disable software IRQ affinity for 1850/2850 systems]. |
|||
* [http://lists.xensource.com/archives/html/xen-users/2006-02/msg00851.html Discussion in xen-users mailing list] |
|||
[[Category:Xen]] |
[[Category:Xen]] |
||
Latest revision as of 01:20, 8 October 2014
I have problems getting Xen or dom0 kernel to boot, how can I set up a serial console to log and troubleshoot the boot process?
See the XenSerialConsole wiki page.
I am booting my new EFI-based system. I se "Loading ramdisk..." and then it stops
Go into your BIOS and enable Legacy Booting (non-EFI). If it still doesn't work, upgrade the BIOS to its latest version.
